 |
Solutions for Time and Frequency Synchronization |
| Products | Support | Downloads | About Meinberg | Contact | Search |  |
| by Application | by Time Source | by Form Factor | Time Server | Product Archive | ||
 |
|
|
DCF77 Radio Clock - PCI/PCI-X Bus
 The PCI511 is a DCF77 radio clock for synchronization of computers with a PCI or PCI-X slot. It receives the longwave radio time signal from the DCF77 sender located near Frankfurt/Main, Germany.
GPS Time Server
 The M300 uses a built-in GPS radio clock as its reference time source
Time Server
 Meinberg NTP Products - Time Server, PCI Cards, external Reference Clocks, Displays
Time Synchronization
 Meinberg NTP Products - Time Server, PCI Cards, external Reference Clocks, Displays
Rackmount Time Server
 LANTIME M600/GPS: PTPv2/IEEE 1588-2008 Grandmaster Clock and NTP Time Server with integrated GPS radio clock.
IPV6 Time server
 The M300/RDT is synchronized by any external Meinberg radio clock (Stratum 1 mode) or up to 7 external NTP time servers (Stratum 2 mode)
IRIG Time Server
 The M300/TCR comes with a built-in TCR module which decodes a IRIG/AFNOR signal from any compatible time code generator.
Timecode Reader
 The TCR51USB is a Timecode Reader in a compact plastic housing - decodes IRIG modulated and unmodulated MEINBERG: Quality Management System
|
Key Features
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||
| Type of receiver: | Narrowband DCF77 quadrature receiver with automatic gain control, bandwidth: approx. 20Hz |
| Type of antenna: | DCF77 indoor antenna AI01 |
| Display: | LC-display, 4 x 16 characters |
| Status info: | LEDs for power (integrated power supply), modulation and RF amplitude |
| Accuracy free run: | Accuracy of the quartz base after min. 24hrs of synchronized operation: ±1·10-6 |
| Reception Control: | Multiple check of received time telegram Plausibility control by using two complete time telegrams |
| Pulse outputs: | Slave clock lines (second and minute line) for analog slave clocks, output shorted slave line detection and autotracking of the slave clocks potential separation between power and control parts pulse voltage: 24V pulse current: 0,6A max. pulse width: 1sec (minute line), 0.5sec (second line) |
| Interface: | Two independent serial RS232-interfaces, menu configurable |
| Data format of interfaces: | COM0: Baudrate: 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600 Baud Framing: 7E1, 7E2, 7N2, 7O2, 8E1, 8N1, 8N2 one active/passive 20mA current loop output one active/passive 20mA current loop input COM1: Baudrate: 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600 Baud Framing: 7E1, 7E2, 7N2, 7O2, 8E1, 8N1, 8N2 one active/passive 20mA current loop output one active/passive 20mA current loop input Output string: 32 ASCII characters with date, time and status information |
| Relay outputs: | 4 relay outputs (changeover contact), max. 50W load |
| Switch programs: | 8 different plans assigned to the days of the week (holidays included or not) with up to 1024 switching times can be edited by the 4 keys in the frontpanel. Alternative: Pulses can be programmed to the outputs |
| Physical dimensions: | 160mm x 193mm x 131mm (height x width x depth) |
| Dimensions of the front panel: | Milled aluminium, 4 integrated keys for menu routing, 100mm x 160mm |
| Electrical connectors: | 32 pin Phoenix connector (counterpart incl.) BNC coaxial female connector 230V mains cable |
| Power supply: | 230V AC, 50Hz |
| Backup battery type: | In case of supply voltage failure the on-board RTC keeps the time based on XTAL for more than 150 hours (buffer capacitor) Optional: lithium backup battery (life time: 10 years) |
| Current consumption: | ca. 100mA |
| Form Factor: | Bopla RegloCard-Plus 1700, IP43 protected |
| Ambient temperature: | 0 ... 50°C / 32 ... 122°F |
| Humidity: | Max. 85% |
Downloads
|
||
|
|
| [ Home | Products | Top ] |
|