 |
Solutions for Time and Frequency Synchronization |
| Products | Support | Downloads | About Meinberg | Contact | Search |  |
| by Application | by Time Source | by Form Factor | Time Server | Product Archive | ||
 |
|
|
PC Clock
 The IRIG output of the GPS170PCI can be used to synchronize IRIG time code receivers
GPS Time Receiver
 GPS PCI Express Slot Card for high precision computer synchronization
GPS NTP
 LANTIME M300/GPS - Synchronization of NTP and SNTP compatible clients
NTP Time Server
 M600/GPS: High End NTP Time Server with integrated GPS radio clock. It synchronizes all systems either NTP- or SNTP-compatible and uses a built-in GPS radio clock as its reference time source
IRIG Converter
 IRIG Time Code Receiver and Generator for Computers
IRIG PCI
 The TCR511PCI is synchronized by modulated (DC Level Shift) and unmodulated (AM) IRIG and AFNOR time code signals and can be integrated in industrial systems that require high precision.
DCF77 Radio Clock - PCI/PCI-X Bus
 The PCI511 is a DCF77 radio clock for synchronization of computers with a PCI or PCI-X slot. It receives the longwave radio time signal from the DCF77 sender located near Frankfurt/Main, Germany. MEINBERG: Quality Management System
|
Key Features
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Type of receiver: | 6 channel GPS C/A-code receiver |
| Type of antenna: | Remote powered GPS antenna/converter unit, up to 300m distance to antenna with RG58 and up to 700m distance with RG213 cable |
| Status info: | Fail-LED shows that the internal timing has not been synchronized or that a system error occurred Lock-LED shows that the calculation of the position has been achieved after reset |
| Synchronization time: | Max. 1 minute in normal operation mode, approx. 12 minutes after a cold start (discharged buffer battery) |
| Frequency outputs: | Frequency output 10 MHz, TTL level |
| Pulse outputs: | Pulse per second (TTL, RS232 level) and pulse per minute (TTL), pulse duration: 200 msec DCF77 compatible pulses (TTL level), pulse width: 100/200 msec |
| Accuracy of pulse outputs: | < ± 250ns |
| Interface: | Single serial RS232 interface |
| Data format PC interface: | Binary, byte serial (compatible with Meinberg DCF77 Slot Card PCI511) |
| Data format of interfaces: | Baudrate: 300, 600, 1200, 2400, 4800, 9600, 19200 Baud data format: 7N2, 7E1, 7E2, 8E1, 8N1, 8N2 Time telegram: Meinberg Standard-Telegram, SAT, Uni Erlangen (NTP), SPA, NMEA0183 (RMC) or capture-telegramm |
| Unmodulated time code output: | DCLS, TTL into 50 ohm (active high or active low) |
| Modulated time code output: | IRIG AM sine wave signal: 3Vpp (MARK), 1Vpp (SPACE) into 50 ohm |
| Generated time codes: | IRIG B002: 100pps, DCLS signal, no carrier, BCD time of year IRIG B122: 100pps, AM sine wave signal, 1 kHz carrier, BCD time of year IRIG B003: 100pps, DCLS signal, no carrier, BCD time of year, SBS time of day IRIG B123: 100pps, AM sine wave signal, 1kHz carrier, BCD time of year, SBS time of day IEEE1344: Code according to IEEE1344-1995, 100pps, AM sine wave signal, 1kHz carrier, BCD time of year, SBS time of day, IEEE1344 expansion for date, time zone, daylight saving and leap second in Control Funktions Segment AFNOR: Code according to NFS-87500, 100pps, AM sine wave signal, 1kHz carrier, BCD time of year, complete date, SBS time of day |
| Time-Trigger inputs: | Resolution: 100 nsec, triggered by falling TTL slope Time of trigger event readable via computer slot or optional second RS232-interface |
| Electrical connectors: | BNC female connector for antenna BNC female connector for modulated timecode 9 pin sub D male connector |
| Power supply: | +5V, ca. 400mA +12V, ca. 170mA |
| Backup battery type: | When main power supply fails, hardware clock runs free on quartz basis, almanac data is stored in RAM Life time of lithium battery min. 10 years |
| Board type: | PCI card short |
| Ambient temperature: | 0 ... 50°C / 32 ... 122°F |
| Humidity: | Max. 85% |
| Options: | Additional RS232 interface |
Downloads
|
||
|
|
| [ Home | Products | Top ] |
|