 |
Solutions for Time and Frequency Synchronization |
| Products | Support | Downloads | About Meinberg | Contact | Search |  |
| by Application | by Time Source | by Form Factor | Time Server | Product Archive | ||
 |
|
|
NTP Clock
 GPS170PCI slot card as time source for your network
Network Time Server
 The M300 time server are designed to be deployed in IPv6 networks
GPS Time Receiver
 GPS PCI Express Slot Card for high precision computer synchronization
NTP Time Server
 M600/GPS: High End NTP Time Server with integrated GPS radio clock. It synchronizes all systems either NTP- or SNTP-compatible and uses a built-in GPS radio clock as its reference time source
Timeserver
 Meinberg NTP Products: Time Server, PCI Cards, external Reference Clocks, Displays
Time Synchronisation
 We offer you a wide range of solutions for synchronizing networks of any size
Rackmount Time Server
 LANTIME M600/GPS: PTPv2/IEEE 1588-2008 Grandmaster Clock and NTP Time Server with integrated GPS radio clock.
IPV6 Time server
 The M300/RDT is synchronized by any external Meinberg radio clock (Stratum 1 mode) or up to 7 external NTP time servers (Stratum 2 mode) MEINBERG: Quality Management System
|
Key Features
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Type of receiver: | 6 channel GPS C/A-code receiver |
| Type of antenna: | Remote powered GPS antenna/converter unit, up to 300m distance to antenna with RG58 and up to 700m distance with RG213 cable |
| Control elements: | Three LEDs to display the status of the programmable outputs one covered key (BSL) to initiate firmware update via COM0 |
| Status info: | Fail-LED shows that the internal timing has not been synchronized or that a system error occurred Lock-LED shows that the calculation of the position has been achieved after reset |
| Synchronization time: | Max. 1 minute in normal operation mode, approx. 12 minutes after a cold start (discharged buffer battery) |
| Accuracy of pulse outputs: | Better than ±250 nsec after synchronization and 20 minutes of operation better than ±3 µsec during the first 20 minutes of operation |
| Interface: | Two independent serial RS232 interfaces, (optional COM1 as RS485) |
| Data format of interfaces: | Baudrate: 300 to 19200 baud Framing: 7N2, 7E1, 7E2, 8E1, 8N1, 8N2 Time strings: Meinberg Standard, SAT, Uni Erlangen (NTP), NMEA0183 (RMC), Computime |
| DCF77 emulation: | Amplitude modulated 77.5 kHz sinewave carrier output level approximately -55 dBm (unmodulated) |
| Optocoupler outputs : | 3 optocoupler outputs; Uce_max = 55V, Ic_max = 50mA, Ptot = 150mW, Ui = 5000Vrms the following operating modes are possible for each channel: - free programmable cyclic or fixed pulses - timer mode; three 'ON'- and three 'OFF'-times programmable per day and channel - receiver state; synchronous state of the GPS-receiver is indicated - DCF77-emulation - Time code (IRIG/AFNOR) - Time string (time telegram of COM1) The switching state of each channel can be inverted, the pulse duration is settable in steps of 10 msec from 10 msec to 10 sec. The outputs can be enabled either: - always (immediately after reset) - only if receiver is GPS-synchronized |
| Generated time codes: | IRIG codes B002/B122, B003/B123, IEEE1344 or AFNOR NFS87-500 modulated output: - IRIG: sinewave 3Vpp (High), 1Vpp (Low) into 50 ohm - AFNOR: sinewave 2,17Vpp (High), 0,69Vpp (Low) into 600 ohm unmodulated outputs: - RS422 - TTL into 50 Ohm - FET with internal pull-up (470 ohm to +5V) |
| Physical dimensions: | GPS164DHS: 105 mm x 85 mm x 104 mm (h x w x d) for 35mm DIN mounting rail GPS164AHS/GPS164DAHS: 105 mm x 125,5 mm x 104 mm (h x w x d) for 35mm DIN mounting rail |
| Electrical connectors: | 8 pole screw terminal for connecting the pulse/switch outputs and the power supply BNC connectors for DCF77-simulation and modulated timecode output female Sub-Min-D connectors for serial interfaces and unmodulated timecode outputs |
| Antenna connector: | BNC-connector |
| Power supply: | GPS164DHS: 19 ... 72VDC GPS164AHS: 100 ... 240VAC, 47 ... 63Hz GPS164DAHS: 100 ... 240VDC |
| Power consumption: | ca. 5W |
| Backup battery type: | When main power supply fails, hardware clock runs free on quartz basis, almanac data is stored in RAM Life time of lithium battery min. 10 years |
| Firmware: | Flash-EPROM, bootstrap loader |
| Ambient temperature: | 0 ... 50°C / 32 ... 122°F |
| Humidity: | Max. 85% |
| Options: | Photo-MOS-relay-outputs; U = 400V, I = 150mA, P = 360mW Ui = 1500VAC instead of optocouplers |
| Deployment in special environments: | The GPS164 and its variants are already deployed to numerous customers in the power industry. They are used for electrical substation synchronization all over the world, for example in South America, the USA and Europe. This product is therefore suitable to work under harsh conditions and still provide reliable and accurate synchronization. |
| RoHS-Status of the product: | This product is fully RoHS compliant |
| WEEE status of the product: | This product is handled as a B2B category product. In order to secure a WEEE compliant waste disposal it has to be returned to the manufacturer. Any transportation expenses for returning this product (at its end of life) have to be incurred by the end user, whereas Meinberg will bear the costs for the waste disposal itself. |
Downloads
|
||
|
|
| [ Home | Products | Top ] |
|
