 |
Solutions for Time and Frequency Synchronization |
| Products | Support | Downloads | About Meinberg | Contact | Search |  |
| by Application | by Time Source | by Form Factor | Time Server | Product Archive | ||
 |
|
|
PC Clock
 The IRIG output of the GPS170PCI can be used to synchronize IRIG time code receivers
GPS Time Server
 The M300 uses a built-in GPS radio clock as its reference time source
Clock GPS Time
 This GPS180PEX PCI EXPRESS slot card is the best choice for adding a highly accurate time base to your servers or workstations
NTP Time Server
 M600/GPS: High End NTP Time Server with integrated GPS radio clock. It synchronizes all systems either NTP- or SNTP-compatible and uses a built-in GPS radio clock as its reference time source
Time Server
 Meinberg NTP Products - Time Server, PCI Cards, external Reference Clocks, Displays
Time Synchronization
 Meinberg NTP Products - Time Server, PCI Cards, external Reference Clocks, Displays
IEEE 1588-2008 Time Server
 The M600/GPS PTP synchronizes all PTPv2/IEEE 1588-2008 compatible clients and systems either NTP- or SNTP-compatible
IPV6 Time server
 The M300/RDT is synchronized by any external Meinberg radio clock (Stratum 1 mode) or up to 7 external NTP time servers (Stratum 2 mode) MEINBERG: Quality Management System
|
Key Features
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Type of receiver: | 6 channel GPS C/A-code receiver |
| Type of antenna: | Remote powered GPS antenna/converter unit, up to 300m distance to antenna with RG58 and up to 700m distance with RG213 cable |
| Control elements: | Three LEDs to display the status of the programmable outputs one covered key (BSL) to initiate firmware update via COM0 |
| Status info: | Fail-LED shows that the internal timing has not been synchronized or that a system error occurred Lock-LED shows that the calculation of the position has been achieved after reset |
| Synchronization time: | Max. 1 minute in normal operation mode, approx. 12 minutes after a cold start (discharged buffer battery) |
| Accuracy of pulse outputs: | Better than ±1 µsec after synchronization and 20 minutes of operation better than ±3 µsec during the first 20 minutes of operatio |
| Interface: | Two independent serial RS232 interfaces, (optional COM1 as RS485) |
| Data format of interfaces: | COM0: Baudrate: 300 to 19200 baud Framing: 7N2, 7E1, 7E2, 8E1, 8N1, 8N2 COM1: Baudrate: 300 to 19200 baud Framing: 7E2, 8E1, 8N1, 8O1 Time string: Meinberg Standard, SAT, Uni Erlangen (NTP), SPA, NMEA0183 (RMC) |
| DCF77 emulation: | Amplitude modulated 77.5 kHz sinewave carrier output level approximately -55 dBm (unmodulated) |
| Optocoupler outputs : | 3 optocoupler outputs; Uce_max = 55V, Ic_max = 50mA, Ptot = 150mW, Ui = 5000Vrms the following operating modes are possible for each channel: - free programmable cyclic or fixed pulses - timer mode; three 'ON'- and three 'OFF'-times programmable per day and channel - receiver state; synchronous state of the GPS-receiver is indicated - DCF77-emulation The switching state of each channel can be inverted, the pulse duration is settable in steps of 10 msec from 10 msec to 10 sec. The outputs can be enabled either: - always (immediately after reset) - only if receiver is GPS-synchronized |
| Physical dimensions: | GPS163DHS: 105 mm x 85 mm x 104 mm (h x w x d) for 35mm DIN mounting rail
GPS163AHS: 105 mm x 125,5 mm x 104 mm (h x w x d) for 35mm DIN mounting rail |
| Electrical connectors: | 8 pole screw terminal for connecting the pulse/switch outputs and the power supply BNC connector for DCF77 signal output female Sub-Min-D connectors for serial interfaces only GPS163AHS: power cord receptacle for AC-line |
| Antenna connector: | BNC-connector |
| Power supply: | GPS163DHS: 19 ... 72VDC GPS163AHS: 100 ... 240VAC, 47 ... 63Hz |
| Power consumption: | ca. 4W |
| Backup battery type: | When main power supply fails, hardware clock runs free on quartz basis, almanac data is stored in RAM Life time of lithium battery min. 10 years |
| Firmware: | Flash-EPROM, bootstrap loader |
| Ambient temperature: | 0 ... 50°C / 32 ... 122°F |
| Humidity: | Max. 85% |
| Options: | Photo-MOS-relay-outputs; U = 400V, I = 150mA, P = 360mW Ui = 1500VAC COM1 as RS485 interface 10MHz frequency output instead of DCF77-emulation via BNC connector |
| RoHS-Status of the product: | This product is fully RoHS compliant |
| WEEE status of the product: | This product is handled as a B2B category product. In order to secure a WEEE compliant waste disposal it has to be returned to the manufacturer. Any transportation expenses for returning this product (at its end of life) have to be incurred by the end user, whereas Meinberg will bear the costs for the waste disposal itself. |
Downloads
|
||
|
|
| [ Home | Products | Top ] |
|